|
|
Line 1: |
Line 1: |
− | Installation of older Knoppix to HDD
| + | {{delete|out of date}} [[User:Werner P. Schulz|Werner P. Schulz]] 01:34, 4 January 2013 (MST) |
− | | + | |
− | - Described installation was tried on Dannix (CZ Knoppix) from 3.7. 2003
| + | |
− | | + | |
− | - Boot Knoppix CD
| + | |
− | | + | |
− | - Run Root Console
| + | |
− | | + | |
− | - Use "fdisk" to create two primary partitions. Larger for OS (for example /dev/hda1
| + | |
− | as type 83 Linux) and smaller for swap (for example /dev/hda2 as type 82 Linux Swap).
| + | |
− | Don't forget to set up bootable attribute "a" to /dev/hda1.
| + | |
− | | + | |
− | - Run "mke2fs /dev/hda1" for initialization of the device
| + | |
− | | + | |
− | - Run "mkdir /mnt/hda1" for creation of the mounting point
| + | |
− | | + | |
− | - Run "mount -t ext2 /dev/hda1 /mnt/hda1" for mounting of the device
| + | |
− | | + | |
− | - Run "cp -a /KNOPPIX/* /mnt/hda1" to copy of needed files
| + | |
− | | + | |
− | - Run "cp /etc/fstab /mnt/hda1/etc" to copy "fstab" file to new system location
| + | |
− | | + | |
− | - Run "chroot /mnt/hda1" for moving to interactive shell
| + | |
− | | + | |
− | - Modify "/etc/fstab" file:
| + | |
− | <pre>
| + | |
− | /dev/hda2 none swap sw 0 0
| + | |
− | /dev/hda1 / ext2 noatime 0 1
| + | |
− |
| + | |
− | none /proc proc defaults 0 0
| + | |
− | none /dev/shm tmpfs defaults 0 0
| + | |
− | | + | |
− | /dev/cdrom /cdrom auto noauto,user 0 0
| + | |
− | /dev/fd0 /floppy auto noauto,user, umask=000 0 0
| + | |
− | </pre>
| + | |
− | | + | |
− | - Run "mkdir /dev/shm" to create of needed directory
| + | |
− | | + | |
− | - Modify "/etc/lilo.conf" file:
| + | |
− | <pre>
| + | |
− | lba32
| + | |
− | boot=/dev/hda
| + | |
− | prompt
| + | |
− | delay=50
| + | |
− | vga=normal
| + | |
− | default=DaNiX
| + | |
− | | + | |
− | image=/vmlinuz
| + | |
− | append="lang=us apm=power-off"
| + | |
− | root=/dev/hda1
| + | |
− | label=DaNiX
| + | |
− | read-write
| + | |
− | </pre>
| + | |
− | | + | |
− | - Run "lilo" for writing of new informatin to MBR
| + | |
− | | + | |
− | - Modify "/etc/init.d/*xsession" file. Find "USER=knoppix" and change it to "USER=root"
| + | |
− | (aproximately 5th line) | + | |
− | | + | |
− | - Reboot Knoppix and then boot it from HDD (NOT from CD!!!)
| + | |
− | | + | |
− | - Run Root Console
| + | |
− | | + | |
− | - Run "mkswap /dev/hda2" for setting up /dev/hda2 as swap device
| + | |
− | | + | |
− | - Reboot Knoppix
| + | |
− | | + | |
− | - The Knoppix system is now installed on your HDD and you can run it as root user.
| + | |
− | | + | |
− | - If you want to run Knoppix OS as a different user (not root), create it (run "adduser").
| + | |
− | | + | |
− | - Modify "/etc/init.d/*xsession" file. Find "USER=root" and change it to "USER=%UserName%" (aproximately 5th line), where %UserName% is the user name of created user.
| + | |
− | | + | |
− | - Run "visudo" to modify "/etc/sudoers". There you have to find and change "knoppix" to "USER=%UserName%", where %UserName% is the user name of created user. This change will allow you to run Root Console.
| + | |
− | | + | |
− | - Reboot Knoppix.
| + | |
− | | + | |
− | [[Category:Hard drive Installation]]
| + | |