Difference between revisions of "Wireless Networking"
Bobeltomate (Talk | contribs) (→Netgear WG111) |
Harry Kuhman (Talk | contribs) m (→General Information On Wireless Card Setup Under Knoppix) |
||
Line 15: | Line 15: | ||
This is a stub for this section, to be added shortly | This is a stub for this section, to be added shortly | ||
− | '''The below sections are specific information on specific make and models of Wireless Networking Adapters and information we currently have on if they are supported in Knoppix or not | + | '''The below sections are specific information on specific make and models of Wireless Networking Adapters and information we currently have on if they are supported in Knoppix or not. Please add your results with your card to the list, and please try to keep the list in alphabetical order.''' |
==== Netgear WG111 ==== | ==== Netgear WG111 ==== |
Revision as of 22:39, 5 September 2005
Contents
Wireless Networking Overview
This is a stub for a section on wireless networking, to be added soon.
Linux Wireless Network Issues
This is a stub for this section, to be added shortly
Wireless Networking Security Issues
This is a stub for this section, to be added shortly
General Information On Wireless Card Setup Under Knoppix
This is a stub for this section, to be added shortly
The below sections are specific information on specific make and models of Wireless Networking Adapters and information we currently have on if they are supported in Knoppix or not. Please add your results with your card to the list, and please try to keep the list in alphabetical order.
Netgear WG111
Configuring the WG111 to use WPA-PSK on a wireless network
This card works very well in Knoppix 3.9, but is as of yet untested in other versions (to my knowledge).
- Commands:
Assuming that the drivers are on the cd in /dev/cdrom, then
mount /dev/cdrom/ /mnt/cdrom/
Find ndiswrapper configuration under Knoppix->Network/Internet and select netwg111.inf from /mnt/cdrom. After that finishes, create the configuration file that you will need shortly using the following command:
wpa_passphrase MySSIDHere MyPassphraseHere > /home/knoppix/wpa_supplicant.conf
Now, use your favorite text editor (if you don't have one, try Kate under the menu item Editors) and edit the /home/knoppix/wpa_supplicant.conf you just created (see below).
With that completed, run the following command. Warning: As it is, the command will monopolize your current command window with potentially useful debugging output, including your encryption key; add -B if you would rather run it in the background (useful when you know it works already), remove -K to hide your key.
sudo wpa_supplicant -ddKt -i wlan0 -c /home/knoppix/wpa_supplicant.conf -Dndiswrapper
The following grabs an IP address if you use DHCP from your router.
sudo pump -i wlan0
And finally, tell Knoppix where to go to find the internet.
sudo route add default gw <Gateway/Router IP address here>
- wpa_supplicant.conf
Note: the bold lines were added in the editing steps for my Linksys WRT54G Router to accept the card. See the Useful Links at the end for a full explanation of all options that can be put in here.
ctrl_interface=/home/knoppix/wpa_supplicant eapol_version=1 ap_scan=1 network={ ssid="MySSIDHere" scan_ssid=1 #psk="MyPassphraseHere" psk=hex representation of the passphrase proto=WPA key_mgmt=WPA-PSK pairwise=TKIP group=TKIP }
- Useful Links:
Wireless card success story (where I located the pump command)
Example wpa_supplicant.conf with full explanations and various configurations
-bobeltomate